1. Slave cylinder
   Clutch shoe
2. Driveshaft
   Coil spring

The driveshaft connects the transmission of your vehicle with the differential. It rotates, which in turn powers the wheels through the differential to move your car forward.

1. Distributor
   Fuel gauge
2. Ignition switch
   Fuel pressure sensor

The ignition switch is the master switch in a vehicle. It supplies all the electrical components, ECU, ignition systems, and fuel systems with power. It transfers power from the battery to the starter motor, which helps turn the engine over.

1. Pit-man arm
   Throttle body
2. Alternator
   Ball joint

Alternators in modern cars charge the battery and power the electrical system when the engine is on.

1. Fuel hose
   Radiator hose
2. Sump
   Water pump

A water pump moves coolant from the radiator through the engine's cylinder head, to keep it cool.

1. Battery
   Glow plug
2. Starter motor
   Solenoid

The starter motor is usually a small 12-volt DC magnet motor that is essential in starting a car when the key is turned. It has a small gear that connects to another larger one on the flywheel, which helps to turn the engine over.

1. Motor mount
   Wheel well
2. Quarter panel
   Deck lid

The motor mount is where the engine is secured to the body of the vehicle. It also offers a cushioned impact for the engine when riding on a bumpy road.

1. Camshaft
   Crank case
2. Connecting rod
   Engine block

An engine component, the camshaft is needed to open and close the engine valves. It consists of a metal shaft that is placed in line with the engine cylinders.

1. Oil filter
   Distributor cap
2. Ignition coil connector
   Hoses (coolant , fuel, and more)

A range of hoses can be found all over a vehicle, including those that carry fuel, coolant and oil.

1. Coil connector
   Magneto
2. Spark plugs
   Dynamometer

The spark from a spark plug is key in starting an engine. This spark causes combustion of the fuel and air mixture, which then starts the engine and keeps it running.

1. Door lock actuator
   Deck lid
2. Hinge
   Slip rings

This is a tiny electric motor that locks or unlocks your doors. That's actually true.

1. Gas tank
   Battery
2. Gas cap
   Fastener

The gas cap covers the opening into the gas tank. It helps to prevent gas from evaporating out of the tank.

1. Air filter
   Differential
2. AC compressor
   Carrier assembly

The air conditioning compressor is at the heart of your climate control unit. It first pressurizes the refrigerant in the system and then circulates it through the system.

1. Thermostat
   Fuel cap
2. Radiator
   Brake pump

A thermostat is a small device between the radiator and the engine. It makes sure no coolant goes into the engine until it has warmed up enough.

1. Exhaust manifold
   Heat shield
2. Catalytic converter
   Muffler

A muffler is mounted on the exhaust pipe in a vehicle. Its primary job is to lower the sound output of the engine.

1. Alternator
   Wiper motor
2. Oil pump
   Hydrometer

The wiper motor is a small motor that drives the windshield wipers on a vehicle. In Britain, this motor drives the windscreen wipers.

1. Crankshaft oil seal
   Head gasket
2. Valve cover
   Brake piston

A head gasket is placed between the cylinder head and the engine block. It forms a tight seal to enclose the combustion process in the engine. It also stops oil and coolant fluid from mixing.

1. Clutch disk and pressure plate
   Brake pedal
2. Grab handle
   Hub cap

Simply put, a clutch is a connection between a vehicle's engine and its wheels. It transfers the power generated by the engine through the transmission to the wheels to make your car move forward. It also detaches the engine from the transmission when stopping.

1. Piston rings
   Brake piston
2. Engine valve
   Poppet valve

Piston rings serve three functions in an engine. They ensure the combustion chamber is sealed. They also increase the transfer of heat from the pistons to the cylinder wall. Finally, they help control oil consumption by collecting excess oil off the cylinder walls.

1. Clutch lever
   Gear pump
2. Slave cylinder
   Ball joint

This joint is the connection between the steering knuckles and the control arm. Each joint consists of a steel bearing stud, enclosed in a casing together with a socket. It acts as a fulcrum between the suspension of a vehicle and its wheels.

1. Ignition coil
   Ammeter
2. Voltmeter
   Battery cable

The ignition coil is found in a vehicle's ignition. It carries low volts from the battery and turns them into thousands of volts that cause a spark in the spark plug. This then ignites the fuel.

1. Master cylinder
   Rack end
2. Fan belt
   Control arm

This is a suspension link (normally hinged) that connects the chassis of the car to the hub in which the wheel is connected.

1. Slave cylinder
   Flywheel
2. Transmission pan
   Torque converter

The flywheel is a heavy disk, connected to the crankshaft at the back of the engine. Its mass keeps a car's engine rotating between ignition strokes. It also provides the clutch something to latch on to, thus helping to deliver power through the transmission.

1. Remote lock
   Heater core
2. Fuel level sensor
   Hydrometer

The heater core contains a winding tube that is filled with warm coolant liquid directly from the engine. This helps heat the interior of the car in cold conditions.

1. Fuel pump
   Radiator
2. Manifold cover
   Carburetor

A carburetor has three important functions. First, it mixes fuel and air to create a combustible mixture. Second, it controls the proportion of fuel and air. Lastly, it controls the speed of the engine.

1. Engine control unit
   Air conditioning unit
2. Door switch
   Fuse box

The engine control unit helps to ensure that a car's engine is running optimally and efficiently at all times. It does this by using a number of actuators.

1. Sump
   Fuel tank
2. Oil filter
   Radiator

The radiator is part of the cooling system that stops a vehicle's engine from overheating. It is filled with water.

1. Blower motor
   Coolant liquid
2. Tappet
   Valve cover

A blower motor moves either hot or cool air (depending on your air-conditioning selection) through the vents of your car and into the cabin.

1. Crankshaft
   Kingpin
2. Idler arm
   Battery

A critical part of the engine, a crankshaft transforms the reciprocating (up and down) motion of the pistons into rotational motion. This, in turn, moves your car forward.

1. Camshaft
   Fuel pump
2. Throttle body
   Oil filter

A fuel pump is needed to transfer fuel from the fuel tank to a car's engine. Without it, the car will not run.

1. Cigarette lighter
   Distributor cap
2. Camshaft position sensor

A camshaft position sensor is critical for the synchronization of injectors, as well as the proper sequence for coils to fire. They also are needed for establishing engine speed and RPM signals, as well as setting ignition timing.

1. Load sensing valve
   Metering valve
2. Rocker cover
   Mass air flow sensor

The mass air flow sensor calculates the mass flow rate of the air passing into a combustion engine with fuel injection. This is critical information which allows the engine control unit to deliver the right amount of fuel to the engine.

1. Headlight
   ABS control unit
2. Catalytic converter
   Fuel pump

An essential part of the braking system on your car, the ABS control unit continually scans the speed of all wheels and ensures that any wheels turning slower or faster either receive reduced or more braking force when the brakes are applied. This keeps traction even at all times.

1. Power steering assembly
   Spiral spring
2. Steering rack
   Carrier assembly

The steering rack connects to the steering wheel. It is a direct link between the tires and the steering wheel.

1. Power window switch
   Spindle
2. Combination valve
   Fuel pressure sensor

The power window switch moves the power windows in a vehicle to open and close them. Each door has a switch, but the driver can operate all of the windows as well.

1. Brake light switch
   Thermostat
2. Suspension coil

A brake light switch is a link between your brake pedal and your brake lights. Every time you press your brake pedal, the switch is activated. which then turns your brake lights on, alerting people behind you that you are slowing down.

1. Shoe web
   Combination valve
2. Wheel stud
   Brake clipper

Brake clippers are used mainly to stop your brake pads from rattling. They are snapped into place when replacing the brake shoes on your vehicle.

1. Glow plug
   Fuse
2. Crankshaft seal
   Door contact

The crankshaft seal is a piece of rubber, found at the front of the engine. It seals the timing cover and the crankshaft's front section.

1. Bell housing
   Axle shafts
2. Universal joint
   Transmission

Axle shafts attach the car wheels to the gears and form part of the transmission, which allows the wheels to turn.

1. Mass airflow sensors
   Intake manifold gasket
2. Interior harness
   Roll cage

The intake manifold gasket produces a seal in the intake manifold. It ensures that the air-fuel mixture is directed to the correct cylinder, where it ignites and burns, creating engine power.

1. Steering angle sensor
   Fuel injector nozzle
2. Stub axle
   Idler arm

The steering angle sensor forms part of the ESC system in a vehicle. It calculates both the steering wheel's position and its turn rate.

1. Nut
   Air spring
2. Resonator
   Wheel speed sensor

The wheel speed sensor is part of the anti-lock braking system. It tells the A.B.S. unit how fast the wheels are turning and how much brake pressure to apply to stop the vehicle from veering out of control or skidding.

1. Oxygen sensor
   Fuel injector
2. Spindle
   Gear ring

Mounted inside the exhaust manifold, the oxygen sensor calculates the amount of unburned oxygen that exits through the exhaust. This is used to determine the fuel mixture. Too much oxygen and the fuel mixture is too rich, too little and it is too lean.

1. Sway bar link
   Pan-hard rod
2. Pitman arm
   Tie rod end

A sway bar link is the connection between the sway bar and a car's suspension. A sway bar link is the connection between the sway bar and a car's suspension.

1. Shock absorbers
   McPherson strut
2. Steering arm
   Stub axle

Shock absorbers have two main functions. They keep all four tires on the ground and they control the movement of the suspension while driving.

1. Electronic timing controller
   Solenoid
2. Pressure sensor
   Door switch

Pressure sensors are found throughout the vehicle. They measure fuel and oil pressure, for example.

1. Beam axle
   Fuel cell
2. Oil strainer
   Oil cooler

This small radiator is essential in making sure the oil running through the engine is kept as cool as possible and at a regulated temperature. The oil cooler helps to ensure a smooth running engine.

1. Rear reflectors
   Dome lights
2. License plate lights / tail lamps
   Trunk reflectors

License plate lights are a simple set of lights, either set above or below the license plate, designed to provide illumination in the dark.

1. Mounting
   Brake rotor
2. Harmonic balancer
   Air duct

This is a major component of the braking system for your vehicle. When you apply the brakes, the brake disks clamp to the rotor, slowing the car down.

1. Fuel gauge
   EGR valve
2. Temperature sensor
   Clutch lever

The temperature sensor monitors the temperature of the coolant running through the engine. That makes sense.

1. Flange
   Overflow tank
2. Catalytic converter
   Exhaust manifold gaskets

Exhaust manifold gaskets are necessary to provide a seal between the exhaust manifold and the cylinder head.